MIG (GMAW) Welding

Miller - Welders - MIG - Millermatic 140 with Auto-Set $625.00 MIL 907335 Processes: MIG (GMAW), Flux-Cored (FCAW) Dimensions: H: 15 3/4in (400mm), W: 10 5/8in (270mm), D: 17 1/2in (445mm) Net Weight: 60 LB (27kg) • NEW! Spool gun compatible. Finally a reliable and economical way to weld aluminum. Hooked up to a Millermatic 140 with Auto-Set, the NEW Spoolmate™ 100 Series spool gun allows you to weld from 18 - 24 gauge aluminum. • Smooth-Start™ patent-pending technology provides a smooth, spatter-free start. It's the best starting machine in the small MIG category. No pop gun starts and no spatter to clean up. • Durable cast aluminum feedhead incorporates dual-groove quick-change drove roll and spring-loaded tension arm with calibrated tension knob, all designed to make set up easier and faster. • "Tip Saver" short circuit protection shuts down output when tip is shorted to the work. Extends contact tip life and protects internal components from damage. Trigger reset permits quick reset at torch rather than unit. • Standard built-in solid-state contractor circuit makes wire electrically "cold" until trigger is pulled, making the unit safer. It's also easier to position torch to work before starting weld. • Thermal overload protection shuts down unit and activates over temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools. • Easy access to output studs provides convenient polarity changeover when switching from solid or flux cored wires. • Uses 4 or 8 in (102 or 203 mm) spools and can be set up to weld with wire sizes .024-.030 in (0.6-0.8 mm) mild/stainless steel and .030-.035 in (0.8-0.9 mm) flux cored. Includes: 10 ft (3 m) M-10 MIG gun and cable assembly #195 605 10 ft (3 m) work cable with clamp Factory-installed gas solenoid valve Smith® regulator and gas hose 6 ft (1.8 m) power cord with plug Dual groove quick-change drive roll for .024 in (0.6 m) or .030/.035 in (0.8/0.9 mm) wire Extra contact tips Hobart® spool of solid wire Information/settings chart Set-up and operation CD Material thickness gauge #229 895 Case Pack: 1 UOM: Each Quantity

Hobart - Welders - MIG - Handler 140 $607.00 The Handler 135 operates off 115 volt standard household current for maximum versatility. Comes ready to weld with or without shielding gas, no additional kit required. Processes: MIG (GMAW), Flux Cored (FCAW) Dimensions: H: 12 3/8 in (315 mm), W: 10 5/8 in (270 mm), D: 18 7/8 in (480 mm) Net Weight: 55 lb (25k kg) • Welds 22 gauge up to 3/16 inch in a single pass • Proven built-in wire feeder with quick-release drive roll lever • Built-in contactor eases use and is an excellent safety feature which makes wire electrically "cold" when not welding. • Four output voltage settings with wire feed tracking provide quick and easy adjustment for different materials and thickness. • Separate "purge" setting to purge gas line and set flow rate without wasting wire • Easy access to polarity changeover includes storage holes for spare tips • Dual groove drive rolls make it easy to switch between .023/.025 in. (0.6mm) and .030 - .035 in. (0.8 - 0.9 mm) wire • Self-resetting thermal overload and motor protection Case Pack: 1 UOM: Each Quantity

Miller - Welders - MIG - Millermatic 180 with Auto-Set $759.95 MIL 907312 Processes: MIG (GMAW), Flux-Cored (FCAW) Dimensions: H: 15 3/4in (400mm), W: 10 5/8in (270mm), D: 17 1/2in (445mm) Net Weight: 72 LB (33kg) • NEW! Millermatic 180 with Auto-Set™ features the breakthrough control that automatically sets your welder to the proper parameters. It works with .024 and .030 in solid steel wire, (75 percent argon/25 percent CO2) shielding gas, and provides all-in-one MIG, minus the guesswork. Just set the wire size, set the material thickness, and start welding. • Spool gun compatible. Finally a reliable and economical way to weld aluminum. Hooked up to a Millermatic 180 with Auto-Set, the NEW Spoolmate™ 100 Series spool gun allows you to weld from 18 gauge - 1/4 inch aluminum. • Welds thickest metal in class - up to 5/16 in mild steel in a single pass! • Smooth-Start™ patent-pending technology provides a smooth, spatter-free start. • Durable cast aluminum feedhead incorporates dual-groove quick-change drove roll and calibrated, spring-loaded tension arm designed to make set up easier and faster. • "Tip Saver" short circuit protection shuts down output when tip is shorted to the work. Extends contact tip life and protects internal components from damage. Trigger reset permits quick reset at torch rather than unit. • Standard built-in solid-state contractor circuit makes wire electrically "cold" until trigger is pulled, making the unit safer. It's also easier to position torch to work before starting weld. • Thermal overload protection shuts down unit and activates over temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools. Includes: 10 ft (3 m) M-10 MIG gun and cable assembly #195 605 10 ft (3 m) work cable with clamp Factory-installed gas solenoid valve Smith® regulator and gas hose 6 ft (1.8 m) power cord with plug Dual groove quick-change drive roll for .024 in (0.6 m) or .030/.035 in (0.8/0.9 mm) wire Extra contact tips Hobart® spool of solid wire Information/settings chart Set-up and operation CD Material thickness gauge #229 895 Case Pack: 1 UOM: Each Quantity

Miller - Welders - MIG - Millermatic 140 $764.00 $649.40 On Sale! MIL 907311 Millermatic 140 with Auto-Set™ Class: Light Industrial Light Industrial Applications: Light Fabrication, Maintenance and Repair, Auto Body, and Farm/Home Input Power: 115 V, 20 A, 60 Hz, Single Phase Rated Output: 90 A at 18 VDC, 20% Duty Cycle, 63 A at 21 VDC, 20% Duty Cycle Processes: MIG (GMAW), Flux Cored (FCAW) Amperage Range: 30 - 140 A Max. Open-Circuit Voltage: 28 • New! Auto-Set™ is a breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG, minus the guesswork! • New! Smooth-Start™ patent-pending technology provides a smooth, spatter-free start. It's the best-starting machine in the small MIG machine category. No pop gun starts and no spatter to clean up. • Durable cast aluminum feedhead incorporates dual groove quick-change drive roll and calibrated, spring-loaded tension arm designed to make setup easier and faster. • Thermal overload protection shuts down unit and activates over temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools. • "Tip Saver" short circuit protection shuts down output when tip is shorted to the work. Extends contact tip life and protects internal components from damage. Trigger reset permits quick reset at torch rather then unit. • Self-resetting motor protection circuit eliminates the need to find and replace fuses. • Easy access to output studs provides convenient polarity changeover when changing from solid or flux cored wires. • Semiautomatic constant voltage wire welding package is capable of welding 24 guage up to 3/16 in (0.8 - 4.8 mm) mild steel. • Standard built-in solid-state contactor circuit makes wire electrically "cold" until trigger is pulled, making the unit safer. It's also easier to position torch to work before starting weld. • Uses 4 or 8 in (102 or 203 mm) spools and can be set up to weld with mild/stainless steel and .030 - .035 in (0.8 - 0.9 mm) flux cored. Comes complete with: Power source 6 ft (1.8 m) power cord and plug 10 ft (3 m) M-10 MIG gun and cable assembly 10 ft (3 m) work cable and clamp Smith™ Argon and AR/CO2 mix regulator/flow gauge with hose Spool of Hobart® .024 in (0.6 mm) solid wire Two contact tips for .024 in (0.6 mm) wire and two contact tips for .030 in (0.8 mm) wire Dual groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) wire Factory-installed gas solenoid valve Information/settings chart Set-up and operation video Material thickness gauge Note: Shielding gas and safety equipment not included. Case Pack: 1 UOM: Each Quantity

ESAB - Welders - MIG - Migmaster 173 ESA 0558005173 The ESAB Migmaster 173 is currently On Sale right now on our home page Pricing good until June 1, 2008. Quantity

Miller - Welders - MIG - Millermatic Passport Plus $1,495.00 MIL 907401 Processes: MIG (GMAW), Flux-Cored (FCAW) Dimensions: H: 15 1/2in (394mm), W: 12in (305mm), D: 20 1/2in (520mm) Net Weight: 45 LB (20.4kg) • NEW! Spool gun compatible. Simply hook up the new Spoolmate™ 100 Series spool gun and now you can tackle any aluminum job from 18 ga - 1/4 in. • The Passport will take you everywhere you need to go. Portability is number one when you have to go to the job - because it can't come to you. The Passport contains all you need to weld in one small lightweight package. • Excellent arc characteristics! The Passport Plus offers positive arc starts and an extremely stable arc with minimal spatter on both mixed gases and straight CO2. • Flexibility to use either external or internal gas cylinder. Self-contained gas cylinder provides 25 minutes of welding time. The cylinder holds 12 oz of CO2. That's 25 ft of weld on 3/16 in thick material with .030 in mild steel wire. • Miller's exclusive multi-voltage plug (MVP™) allows connection to 115 or 230 V receptacles without tools - choose the plug that fits the receptacle and connect it to the power cord. • Auto-Line™ provides state-of-the-art flexibility, automatically connecting to 115/230 VAC, single-phase power. • Impact-resistant case provides strength and durability, protecting the internal components and welding wire. Includes: 10 ft (3 m) power cord and MVP™ adapter plugs for 115 and 230 V 10 ft (3 m) M-10 MIG gun and cable assembly #195 605 10 ff (3 m) work cable with clamp One CO2 gas cylinder (empty) Dual-groove, quick-change drive rolls for .024 in (0.6 mm) and .030/.035 in (0.8/0.9 mm) wire Two contact tips for .024 in (0.6 mm) wire and two for .030 in (0.8 mm) wire Case Pack: 1 UOM: Each Quantity

Miller - Welders - MIG - Millermatic DVI2 $1,509.00 $1,282.65 On Sale! MIL 907323 - SALE Quantity

Hobart - Welders - MIG - IronMan 210 $1,529.00 MIL 500304 An economical all-in-one MIG machine that is both versatile and portable, the IronMan™ 210 has outstanding arc characteristics from excellent short arc performance to an easy-to-control weld puddle. Unit has Constant-voltage DC power source Processes: MIG (GMAW), Flux Cored (FCAW) Dimensions: H: 31in (794mm), W: 18 7/8in (479 mm), D: 36in (927 mm) Net Weight: 144lb (65kg) • Welds 22 gauge up to 3/8 inch material in a single pass Excellent aluminum welding with optional Spoolmate™ 3035 spool gun, no module needed for hookup • Easy-to-set, six-tap voltage control allows for a smooth easy-to-control arc • Infinite wire feed speed control for precise adjustment of penetration and weld bead shape • Complete package includes gun and built-in running gear/cylinder rack • Handles wire spools up to 12 in (33 lb) - wire feed speed adjusts from 90 to 8/750 IPM • Built-in thermal overload protects the unit • Reversible drive rolls: two grooves for three wire sizes on one drive roll. Decreases spare parts and changeover time • Hinged door for easy access to wire drive system for spool and drive roll changes Case Pack: 1 UOM: Each Quantity

Miller - Welders - MIG - Millermatic 212 $1,683.00 $1,430.55 On Sale! MIL 907324 Processes: MIG (GMAW), Flux-Cored (FCAW) Dimensions: H: 30in (762mm), W: 19in (483mm), D: 40in (1016mm) Net Weight: 190 LB (86kg) • Seven taps provide wider welding range of 30-210 A with superior performance throughout its operating range. • Angled industrial, dual-gear-driven, aluminum drive system features no-tool, quick-change reversible drive rolls and easy-to-set, scaled tension knob. • EZ-Access™ consumable compartment and parameter chart provides convenient flip-down compartment for fast access to consumables and parameter chart. • EZ-Change™ cylinder rack is a low rack that provides safer, easier cylinder loading. Includes: 15 ft (4.5 m) 250 amp M-25 gun 10 ft (3 m) work cable with clamp Factory-installed dual gas solenoids Smith® Argon mix regulator/flow gauge with hose 7 ft (2.1 m) power cord and plug Factory-installed running gear/cylinder rack .035/.045 in reversible dual groove drive rolls Extra contact tips Set-up and operation CD Case Pack: 1 UOM: Each Quantity

ESAB - Welders - MIG - Migmaster 250 ESA 604561 The ESAB Migmaster 250 is currently On Sale right now on our home page Pricing good until June 1, 2008. Quantity

1111 Pierce Butler Route St. Paul, MN 55104 Phone: 651-644-7273 Toll Free: 800-774-1336 Fax: 651-644-2973

info@oxyserv.com

1002 Industrial Drive So Sauk Rapids, MN 56379 Phone: 320-252-5494 Toll Free: 800-252-3275 Fax: 320-230-3300

Everything for Welding!

An Equal Opportunity Employer